Sterndrives.Com     Mercruiser Sterndrive Information
Mercruiser Parts Mercruiser Help Mercruiser Manuals Mercruiser Tools Mercruiser Sterndrives Contact

Mercruiser Mercarb or Rochester?

Mercruiser has used several different types of carburetors over the years.
The Rochester 2 Barrel Carb was popular on the early 4 cylinder models and it
was also used on a few V6 and V8/305 GM engines as well.

Rochester then stopped production so Mercury Marine designed its own version of the
Rochester 2 Barrel Carburetor called the Mercarb.

The Mercarb and Rochesters were mixed in production models.
When ordering replacement carbs, kits or parts you need to know exactly
which carb your engine has.

One simple test can distinguish between a Rochester and a Mercarb.
The throttle base plate of a Rochester Carb has two idle mixture screws.
The throttle base plate of a Mercarb has only one idle mixture screw.

If you have determined that your carb is a Mercarb, then there is one more
identification you need to make.
The Mercarb came with two different styles of accelerator pumps.
One pump rod was straight and cut off flat at the very top. This was the older style.
The other pump rod has a 90 deg bend at the top. This is the newer style.
Old Style
Older Style Accelerator Pump
New Style
Newer Style Accelerator Pump


The earlier style Mercarb Kit (With straight accel pump rod) is 3302-804845 for $69.55


The later style Mercarb Kit (With the 90deg bent accell rod) is 3302-804844002 for $77.11


Prices are subject to change.

The Mercarb Kits include all gaskets and seals, needle/seat, idle mixture screw,
inlet strainer, springs, check balls, mounting gasket and accelerator pump assembly.

Click HERE for a list of Remanufactured Carburetors.
Click HERE for a list of New Carburetors and Carburetor Rebuild Kits.

Safety
Boats can explode. Moving parts can rip off your fingers. Hot exhaust can burn you to the bone and props can slice you up. One spark near a battery can cause an explosion. You can never be too careful. Remove the battery from the boat before working with fuel. Always disconnect the batteries negative terminal first. Clean up any spilt fuel and let ALL of the fumes dissipate before installing the battery and starting the motor. Pulleys and Belts can grab your clothes and hair. Don't wear loose clothing and keep your hair up under a hat. Always wear safety glasses. Be smart.
Sterndrive-Information
Change your Alpha Gear Lube
Change your Bravo Gear Lube
Why does my drive lube have white streaks?
Why does my drive lube have gray mush?
Replace Your Alpha One Water Pump
Replace your Alpha Gen II Water Pump
Rebuild your Bravo Raw Water Pump

Troubleshoot & Replace your Alpha Shift Cable
Troubleshoot & Replace your Bravo Shift Cable

Replace your Alpha One Bellows & Gimbal Bearing
Replace your Alpha Gen II Bellows & Gimbal bearing
Replace your Bravo Bellows & Gimbal Bearing
Why does my drive "Growl" when I turn?
Water is leaking into my boat from the transom

Replacing your Trim Sender Switches
My Trim doesn't work but my Trailer Switch does
My Trim Gauge is Pegged

Rebuild your Alpha One Upper Driveshaft Housing Assembly
Rebuild your Alpha One Lower Gear Housing Assembly

Check your Engine Alignment
Check for Excessive Steering Play
Troubleshoot an Overheating Problem
Should I remove my thermostat?
Why do I overheat when going fast?
Troubleshoot a No-Crank Condition
Troubleshoot a No-Start Condition
My Engine Backfires and/or Surges and has Lack of Power
What is an Anti-Syphon Valve?
My Engine blows Steam from the Exhaust
Why do I hear a "clakity" sound while at idle?
Exhaust Manifolds...IMPORTANT Information
How do I Winterize my engine?

What is Galvanic Corrosion?
I have a Bravo III Galvanic Corrosion Problem
What is a Mercathode?
All about Zinc Anodes
How do I check my carburetor?
What carburetor do I have? A Rochester or a Mercarb?
I have water in my fuel
My fuel smells like varnish
My fuel is old
My engine has been sitting for several months without being run.

I have a Mercruiser 470, 485, 488, 190, 3.7L Engine
I have coolant dripping from the front of my engine
Can I install a regular Alternator instead of the Stator-Rotor?

Converting an OMC to a Mercruiser


©2004 Sterndrives.Com •EmailAbout UsHomeReturn Policy Mercruiser HelpShop ManualsSearchContact